[Mar 23, 2022] Prepare For The HPE6-A75 Question Papers In Advance
HPE6-A75 PDF Dumps Real 2022 Recently Updated Questions
HP HPE6-A75 Exam Syllabus Topics:
| Topic | Details |
|---|---|
| Topic 1 |
|
| Topic 2 |
|
| Topic 3 |
|
| Topic 4 |
|
| Topic 5 |
|
| Topic 6 |
|
| Topic 7 |
|
| Topic 8 |
|
NEW QUESTION 22
in a VPN that uses certificate-based authentication, which component must be configured on the Mobility Master (MM) to allow a RAP to successfully connect to a Mobility Controller (MC)
- A. RAP IPSec pre-shared key
- B. RAP whitelist
- C. RAP VPN username and password
- D. WLAN and new RAP group
Answer: B
NEW QUESTION 23
A company requires AOS-Switches at the campus core. The switches:
Will act as the default gateways for several campus VLANs
Must provide redundancy for their services and tolerate the loss of a link or an entire switch Must recover from the failure of one of the switches within a second or less VRRP and MSTP are proposed to meet these requirements. What is an issue with this proposal?
- A. VRRP does not interoperate with MSTP.
- B. VRRP provides redundancy against lost links but not a failed switch.
- C. VRRP provides routing redundancy but not default gateway redundancy.
- D. VRRP takes longer than a second to fail over.
Answer: D
NEW QUESTION 24
Which technologies can prevent split brain in a VSF fabric that includes Aruba 2930F switches?
- A. VLAN MAD or ARP MAD
- B. ARP MAD or OOBM MAD
- C. OOBM MAD or LLDP MAD
- D. LLDP MAD or VLAN MAD
Answer: D
NEW QUESTION 25
When is it necessary to use an SNMP based Enforcement profile to send a VIAN?
- A. When we have to assign a VLAN to a wireless user on an Aruba Mobility Controller.
- B. When we have to assign a VLAN to a wired user on a third party wired switch that doesn't support RADIUS authentication.
- C. When we have to assign a VIAN to a wired user on an Aruba Mobility Controller.
- D. When we have to assign a VLAN to a wired user on an Aruba Mobility Access Switch.
- E. When we have to assign a vlan to a wired user on a third party wired switch that doesn't support RADIUS return attributes.
Answer: D
NEW QUESTION 26
Which ArubaOS CLl command can an administrator execute to determine if AP load balancing is enabled in a cluster?
- A. show switches
- B. show lc-cluster group-membership
- C. show aaa cluster essid
- D. show ap active
Answer: B
NEW QUESTION 27
Refer to the exhibit.
Switch-1 and Switch-2 connect on interface A23. The switches experience a connectivity issue. The network administrator sees that both switches show this interface as up. The administrator sees the output shown in the exhibit on Switch-1.
What is a typical issue that could cause this output?
- A. mismatched IP addresses on the VLAN for the link
- B. an issue with queuing, caused by mismatched QoS settings
- C. a hardware issue, such as a broken cable
- D. asymmetric routing introduced by a routing configuration error
Answer: C
NEW QUESTION 28
A network administrator configures V5F settings on two Aruba 2930F switches. The switches form two separate VSF fabrics. What should the administrator check?
- A. that the switch with the lower priority has the lower member ID
- B. that each switch is assigned a unique VSF priority
- C. that the domain ID matches on both switches
- D. that LLDP MAD is configured on both members
Answer: A
NEW QUESTION 29
An administrator wants to implement bandwidth limits for guest users to restrict their Internet usage. On the Mobility Master (MM), where would the administrator define these limits?
- A. 802.1X policy
- B. Firewall policy
- C. AAA policy
- D. User role
Answer: B
NEW QUESTION 30
An administrator implements the MultiZone feature and uses two clusters that utilize CPSec. A primary and a data zone are created. MultiZone APs successfully build sessions to the primary cluster but fail to establish sessions to the data zone cluster.
What must the administrator do to solve this problem?
- A. Enable CPSec in the MultiZone profile for both the primary and data zone.
- B. Use different AP Group names for the two zones.
- C. Add the MultiZone APs to the data zone's CPSec whitelist.
- D. Enable MultiZone booting in the MultiZone AP apboot configuration mode.
Answer: B
NEW QUESTION 31
Refer to the exhibit.
A network administrator sets up 802.1X authentication to a RADIUS server on an AOS-Switch. The RADIUS server and user devices are both set up to use REAP MSCHAPv2. The administrator tests the authentication and sees the output shown in the exhibit. Which issue could cause this output?
- A. The administrator entered the wrong password for the test account.
- B. The switch port is set for user mode 801. IX. but the RADIUS server is set for port mode.
- C. The RADIUS shared secret does not match on the switch and the server.
- D. The switch does not have a certificate tor port-access installed on the switch.
Answer: C
NEW QUESTION 32
Refer to the exhibit.
A company has attempted to implement OSPF without success. The devices in Area I need to be able to reach Area 2. Routes should be aggregated for advertisement in other areas. What must be changed to meet these requirements?
- A. Move the 10.1.0.0/16 range to Area 2 on Switch-1 and the 10.2.0.0/16rangetoArea 1 onSwitch-2.
- B. Change Area 3 to Area 0; remove Area 1 from Switch-2 and Area 2 from Switch-1.
- C. Add the 10.2.0.0/16 range on Swttch-1 and the 10.1.0.0/16 range on Switch-2.
- D. Add Area 1 and Area 2 on VIAN 100 on both Switch-1 and Switch-2. Remove Area 3.
Answer: B
NEW QUESTION 33
Refer to the exhibit.
A known unicast packet is received from Switch-1 on the standby and must be forwarded to Switch-2. How does the VSF fabric decide which port in the aggregated (ink should forward the packet?
- A. The standby sends the packet to the commander over a VSF link, and the commander decides the correct port.
- B. The standby selects the port on the designated forwarder for the aggregation.
- C. The standby uses the typical load sharing algorithm, and it might select either its port or the commander's port.
- D. The standby uses its own port in the link aggregation to forward the fabric.
Answer: D
NEW QUESTION 34
OSPF is configured on an AOS-Switch, and the network administrator sets the router ID to 10.0.0.1. The administrator wants to be able to reach the switch at this ID from any location throughout the OSPF system. The administrator also needs the router ID to De stable and available, even if some links on the switch fail.
What should the administrator do?
- A. Configure 10.0.0.1 on a loopback interface, and enable OSPF on that interface.
- B. Make sure that 10.0.0.1 is the IP address on the VLAN with the lowest ID.
- C. Configure 10.0.0.1 as a secondary IP address on the switch 00BM poet.
- D. Configure 10.0.0.1 as a manual OSPF neighbor on each switch in the OSPF system.
Answer: A
NEW QUESTION 35
Why is a terminate session enforcement profile used during posture checks with 802.1 x authentication?
- A. To send a RADIUS CoA message from the ClearPass server to the client
- B. To disconnect the user for 30 seconds when they are in an unhealthy posture state
- C. To remediate the client applications and firewall do that updates can be installed
- D. To force the user to re-authenticate and run through the service flow again
- E. To blacklist the user when they are in an unhealthy posture state
Answer: A
NEW QUESTION 36
Refer to the exhibit.
An AD user's department attribute is configured as *HR". The user connects on Monday using their Windows Laptop to a switch that belongs to the Device Group HQ. Which role is assigned to the user in ClearPass?
- A. iOS Device
- B. Remote Employee
- C. Executive
- D. Vendor
- E. HR Local
Answer: B,E
NEW QUESTION 37
A company has AOS-Switches, Aruba ClearPass, and Aruba Airwave. A network administrator needs to set up a new switch with the same settings found on other switches in the company. Which action rs likely to be the most useful to perform the task?
- A. View usage patterns on the switches on AirWave.
- B. View the current running config on each switch.
- C. Access the Network Device view on ClearPass.
- D. Use the configuration audit tool on AirWave.
Answer: C
NEW QUESTION 38
Refer to the exhibit.
Based on the Policy configuration shown, which VLAN will be assigned when a user with ClearPass role Engineer authenticates to the network successfully on Saturday using connection protocol WEBAUTH?
- A. Full Access VLAN
- B. Internet VLAN
- C. Deny Access
- D. Employee VLAN
Answer: D
NEW QUESTION 39
An administrator supports a RAP to a branch office. Employees at the branch office connect to an employee SSID that allows for split tunneling of the employee traffic. The RAP initially connects to the corporate office controller, but later loses connectivity to it.
Which operating mode should the administrator configure for a secondary SSID to be advertised during the loss of connectivity?
- A. Standard
- B. Backup
- C. Persistent
- D. Always
Answer: C
NEW QUESTION 40
What are Operator Profiles used for?
- A. to assign ClearPass roles to guest users
- B. to enforce role based access control for Aruba Controllers
- C. to enforce role based access control for ClearPass Guest Admin users
- D. to map AD attributes to admin privilege levels in ClearPass Guest
- E. to enforce role based access control for ClearPass Policy Manager admin users
Answer: C
NEW QUESTION 41
Refer to the exhibit.
An employee connects a corporate laptop to the network and authenticates for the first time using EAP-TLS. Based on the Enforcement Policy configuration shown, which Enforcement Profile wilt be sent?
- A. Onboard Pre-Provisioning - Aruba
- B. Deny Access Profile
- C. Onboard Post-Provisioning - Aruba
- D. Onboard Device Repository
Answer: A
NEW QUESTION 42
What is the purpose of the captive portal URL hash key on an AOS-Switch?
- A. It encrypts and secures the RADIUS messages that the AOS-Switch sends to ClearPass.
- B. It specifies the captive portal URL and conceals the setting in the config.
- C. It does not let users alter the URL that redirects them to the portal.
- D. It authenticates guest users based on the password the users enter hi the portal.
Answer: C
NEW QUESTION 43
An administrator configures an ArubaOS-Switch for per -user tunneled node. Which protocols does the switch use to establish and maintain a connection with the Aruba Mobility Controller (MO? (Select two.)
- A. SSL
- B. GRE
- C. PAPI
- D. IPSec
Answer: B,C
NEW QUESTION 44
......
HPE6-A75 Dumps and Practice Test (62 Exam Questions): https://www.itexamsimulator.com/HPE6-A75-brain-dumps.html
Released HP HPE6-A75 Updated Questions PDF: https://drive.google.com/open?id=1SxoD38fLCL1-FGytWLbTSzv4johfm8kL
