[2022] NACE-CIP2-001 Exam Dumps, Test Engine Practice Test Questions
Pass NACE-CIP2-001 exam [Jan 14, 2022] Updated 100 Questions
NEW QUESTION 35
Because a NACE Level 2 Inspector has been trained in specific destructive tests, it is up to the Inspector to decide if and when a destructive test is required.
- A. True
- B. False
Answer: B
NEW QUESTION 36
As a NACE Level 2 Inspector on a field job; prior to submission your documentation should always reviewed and approved by:
- A. A NACE Protective Coating Specialist
- B. Another NACE Level 2 Inspector
- C. A NACE Level 3 Inspector
- D. A NACE Level 1 Inspector
Answer: C
NEW QUESTION 37
You have just your NACE CIP Level 2 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Meet with the prospective employer to scope of your role
- B. Review the NACE Attestation prior to making a decision
- C. Accept assignment without hesitation
- D. Advise the prospective employer that you cannot accept the position
Answer: B
NEW QUESTION 38
In which type of concrete are laitance commonly encountered?
- A. Poured (wet cast)
- B. Concrete block (poured with a form)
- C. Glass fiber cement
- D. Gunite
Answer: A
NEW QUESTION 39
An Inspection and Test Plan is required when:
- A. When the Owner specifies one
- B. It is always required
- C. When the Coating Applicator requests one
- D. When the Inspector requests one
Answer: B
NEW QUESTION 40
NACE/SSPC Water Jetting standards are directly equivalent to ISO Abrasive Blast Standards:
- A. True
- B. False
Answer: B
NEW QUESTION 41
Pre-cleaning of work pieces will NOT remove
- A. oil or grease.
- B. dirt.
- C. mill scale.
- D. snow, ice or water.
Answer: C
NEW QUESTION 42
A failure caused by applying a coating too thinly is known as
- A. cracking.
- B. pinholes.
- C. chalking.
- D. failure to cure.
Answer: B
NEW QUESTION 43
Galvanizing performs best in which of the following exposures:
- A. pH below 4
- B. pH between 5-10
- C. pH above 12
- D. pH of 13
Answer: B
NEW QUESTION 44
You are the NACE Level 2 Inspector on a project where overcoating of galvanized steel is being performed. The specification references SSPC SP 16 as the surface preparation method. At the pre-job meeting operations personnel make it clear that abrasive blasting will not permitted. The Owner's representative asks you what other methods might be used.
Of the options shown below, what would be the preferred option in this situation?
- A. SP 1 followed by caustic etching
- B. SP 1 followed by SP 2
- C. SP 1 followed by SP 3
- D. SP 1 followed by acid etching
Answer: B
NEW QUESTION 45
Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?
- A. High-pressure water washing
- B. Sacking
- C. Stoning
- D. Acid etching
Answer: B
NEW QUESTION 46
Eddy current DFT gauges are used to measure Dry Film Thickness in which of the following situations:
- A. Conductive coatings applied to a cementitious substrate
- B. Conductive coatings applied to a magnetic metallic substrate
- C. Non-Conductive coatings applied to a conductive metallic substrate
- D. Magnetic coatings applied to a magnetic metallic substrate
Answer: C
NEW QUESTION 47
Antifouling coatings are regulated by international treaties.
- A. True
- B. False
Answer: A
NEW QUESTION 48
Inspectors perform tests on linings that they may not perform on exterior coatings because
- A. linings are more durable than coatings.
- B. linings protect the contents and the container.
- C. coatings are expected to degrade over time.
- D. coatings are more durable than linings.
Answer: B
NEW QUESTION 49
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
- A. 3-Layer Polyethylene (PE)
- B. Coal Tar Enamel
- C. Fusion Bonded Epoxy
- D. 2-Layer Polyethylene (PE)
Answer: A
NEW QUESTION 50
You are the NACE Inspector on a project where a stationary floating structure is being coated and you notice a self-smoothing anti-fouling coating has been specified.
This is not a good choice because:
- A. It doesn't contain biocide
- B. The floating structure is stationary
- C. It contains biocide
- D. It will result in a very slippery surface
Answer: C
NEW QUESTION 51
......
NACE NACE-CIP2-001 Real 2022 Braindumps Mock Exam Dumps: https://www.itexamsimulator.com/NACE-CIP2-001-brain-dumps.html
NACE NACE-CIP2-001 Actual Questions and 100% Cover Real Exam Questions: https://drive.google.com/open?id=1e-GebX1Yv50aJIe2ZaJ6nOB-qfSuNPsp
