[Mar-2022] Verified NACE-CIP2-001 dumps Q&As - NACE-CIP2-001 dumps with Correct Answers
The Best CIP Level 2 Study Guide for the NACE-CIP2-001 Exam
NEW QUESTION 24
NACE No.13/ SSPC 6 identifies the use of:
- A. Abrasive blasting only
- B. Watterjetting only
- C. Various methods of cleaning
- D. Steam cleaning only
Answer: C
NEW QUESTION 25
You are working as the only in-house NACE Level 2 Inspector in a shop setting when an independent 3 rd party NACE Level 3 Inspector, representing the owner, presents you with a copy of a Non Conformance Report (NCR) he has written for a NACE2/SSPC SP 10 centrifugal blast which you had previously approved.
Your FIRST preferred course of action is to:
- A. Consult your supervisor
- B. Request a re-blast of the item in question
- C. Review the NCR with the other Inspector
- D. Verbally challenge the NCR
Answer: A
NEW QUESTION 26
Corrosion is the reverse process of
- A. flaking.
- B. galvanic deterioration.
- C. hot dipping.
- D. steel manufacturing.
Answer: D
NEW QUESTION 27
As a NACE Level 2 Inspector, NACE clearly indicates that you ate qualified to independently produce final documentation for a shop project.
- A. True
- B. False
Answer: A
NEW QUESTION 28
Inspection and Test plans are developed by referencing:
- A. The Specification, Safety Manual, Relevant Standards and Codes
- B. The Specification, Application Guidelines, 'Relevant Standards and Codes
- C. The Specification, SDS, relevant Standards and Codes
- D. The Specification, TDS, relevant Standards and Codes
Answer: D
NEW QUESTION 29
WJ-1 is always performed using UHWJ at pressures above 210 MPa (30,000 PSI)
- A. True
- B. False
Answer: A
NEW QUESTION 30
You are the NACE Level 2 Inspector with the final responsibility to prepare the final report for a very large structural steel shop project which has gone very well. It is due next week. The work has been ongoing for two years and several NACE Level 1 Inspectors have worked under your supervision throughout the project. You find you are missing one week of daily reports for the night shift from the very beginning of the project and despite your best efforts they are cannot found.
You FIRST preferred course of action is to:
- A. Re-create the reports as not much was going on during night shift anyway
- B. Plainly state in your report that they are missing
- C. Use creative writing to cover over the fact they are missing
- D. Do not complete your report until they can be found
Answer: B
NEW QUESTION 31
Coating Surveys are legally required:
- A. On commercial marine vessels and offshore platforms
- B. On food and beverage vessels and can linings
- C. On high pressure gas lines and fireproofed structures
- D. On water tanks and potable water pipelines
Answer: A
NEW QUESTION 32
When a coating is expected to be exposed to temperatures above 93C (200 F) the best choice would be:
- A. Organic coatings
- B. Inorganic Coatings
- C. Polyurea
- D. Latex
Answer: B
NEW QUESTION 33
Which is used to calibrate a pH meter?
- A. Deionized water
- B. Standard buffer solution
- C. Distilled water
- D. Standard solvent solution
Answer: B
NEW QUESTION 34
When completing the Final Inspection report the Inspector should write the report using:
- A. Language that only technical experts would understand
- B. Language that another NACE Inspector would understand
- C. Language that the most would understand
- D. Language that only in the project would understand
Answer: C
NEW QUESTION 35
You are the new NACE Level 2 Inspector on a job which had been very problematic. The previous Inspector was fired duo to personality conflicts with the Contractor's supervisor. Upon arriving onsite the Contractor's supervisor advises you in no uncertain terms that you will be the next to go, unless you cooperate with him.
Your FIRST preferred course of action is to:
- A. Express a willingness to work with the site team and follow the specification
- B. Suggest to the Owner that the supervisor should be removed from site
- C. Defend the previous inspector
- D. Challenge the supervisor's authority
Answer: A
NEW QUESTION 36
It is always possible to see moisture on a steel substrate:
- A. False
- B. True
Answer: A
NEW QUESTION 37
When performing testing in accordance with ASTM D 2583 the inspector may observe:
- A. Cohesion failure
- B. Cold flow or creep
- C. Glue failure
- D. Adhesion failure
Answer: B
NEW QUESTION 38
Differences in technique for abrasive blasting concrete versus steel require the operator to:
- A. a), b) and c)
- B. Lower the blast pressure
- C. Increase the standoff distance
- D. Move the nozzle quicker
Answer: A
NEW QUESTION 39
You are NACE Level 2 Inspector working on a tank lining job where a mobile centrifugal blast unit is being used to blast the tank floor to a NACE No.1/SSPC SP 5. The Contractor has completed his final blast and has called for a hold point inspection. This is the 1 st time you have seen field based centrifugal blast cleaning. You observe what appears to be staining on the substrate however the Contractor assures you this is normal when using centrifugal blast units and what you are seeing is what is defined in the standard as an acceptable variation in appearance.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Review the standard with the Contractor and re-inspect the floor
- C. Shut the job down
- D. Request that the Contractor re-blast the floor
Answer: B
NEW QUESTION 40
NACE Standards include:
- A. Material Requirements
- B. a) only
- C. Standard Practices
- D. a) & b)
Answer: D
NEW QUESTION 41
Which standards are generally established by private-sector bodies and are available for use by any person or Organization, private or government?
- A. De facto
- B. Mandatory
- C. Voluntary
- D. Consensus
Answer: C
NEW QUESTION 42
In which type of concrete are laitance commonly encountered?
- A. Glass fiber cement
- B. Poured (wet cast)
- C. Gunite
- D. Concrete block (poured with a form)
Answer: B
NEW QUESTION 43
You are the NACY Coating Inspector on a tank lining project where desiccant dehumidification is being used. Since the first shift of abrasive blasting your readings have indicated relative humidity below 40%; however on the second shift of coating application your readings are indicting 80%.
Your FIRST preferred course of action is to:
- A. Call your supervisor
- B. Check to See if the dehumidification equipment is operating correctly
- C. Advise the coating applicator supervisor of your readings
- D. Document the readings at the end of the shift
Answer: C
NEW QUESTION 44
The cost of qualified Coating Inspection is normally offset by:
- A. Lower Safety Enforcement Costs
- B. Lower Supervision Costs
- C. Lower Application Costs
- D. Lower Coating Life Cycle Costs
Answer: D
NEW QUESTION 45
......
NACE-CIP2-001 certification guide Q&A from Training Expert ITExamSimulator: https://www.itexamsimulator.com/NACE-CIP2-001-brain-dumps.html
NACE-CIP2-001 Certification Overview Latest NACE-CIP2-001 PDF Dumps: https://drive.google.com/open?id=1mYC1wFfiyQDCrupyCOOPWZhKVi19v2PV
